Unfortunately, most owners are increasingly faced with such a problem when the hot water meter does not spin. What to do and what to do in order to avoid such incidents, how not to overpay and for what reasons the hot water meter may break, we will consider in the article.
What is the problem?
To immediately understand the reasons for the failure of the meter after installation or in the first years of service, it is worth noting that the meter lasts about 12 years on average. If the operation process is carried out incorrectly or the mechanism is incorrectly installed, its service life is significantly reduced. There are problems in the winding and winding of indicators, and this is the excess money of the consumer.
So that there are no problems and the operation of the device is correct, do not neglect the advice of a specialist. Perhaps this is extra money, but finding funds every 5 years should not be difficult. The approach can save you money in the future and secure in cases where you are accused of winding the meter. A guaranteed test coupon is your proof that the device has passed the appropriate test and shows reliable information. This is a guarantee of his serviceability and honesty.
What to do in case of failure of the hot water meter, what are the reasons that the hot water meter has stopped working, and what can cause such a problem, let's look in this article.
Problem number 1: the water meter was depressurized
The water meter is a special sealed unit that should not contain suspicious chips, cracks and smudges. If you see something from the above on your counter, most likely, from a stroke or mechanical damage, it has failed. The hot water meter in the apartment stopped working: what should I do?
You can diagnose a breakdown or suspicion of it yourself. Turn off all taps and lock the gauge arrows. Do not turn on the water and refrain from using at least an hour, and preferably 3-4 hours. If after a lapse of time you notice that the readings of the arrow have changed, perhaps the problem is the tightness of the valves being shut off or the pipes themselves. The situation is especially characteristic in old houses, where the pipes are old and rusted.
Quite often it turns out that the cause of this depressurization is a malfunction of the stopcock. Due to its unstable operation, the tap does not tightly shut off the water flow, as a result of which the supply of the resource continues with a partial pressure. This can be clearly expressed in leaking taps and pipes. It is almost impossible to fix the problem yourself. Here we need knowledge in the plumbing business, so you have to call a specialist to solve the problem.
Problem number 2: poor and poor installation of the meter
One of the most unloved reasons for plumbers is damage due to their fault. The fact is that the meter is a very gentle device that will not tolerate rough installation.Not immediately, but over time it leaks or the glass begins to fog up, which indicates its depressurization.
Be sure to double-check that you have purchased the correct meter and installed it correctly before installation. This is pretty simple. Take a look at the description of the device and the footnote of the SVG and TSW. It is cold and hot water. If a device designed for cold water was installed in place of hot water, this is fraught with instant problems in operation. Later, the mechanism will inevitably fail, and in the shortest possible time. Those who notice this problem, note problems with indicators, as well as condensation on the case.
Next, we will consider the most common problem, why did the hot water meter stop working and what should I do?
Problem number 3: old pipes and trash accumulated in them
Clogging is the main reason plumbers face when the hot water meter is not working. What to do?
User reviews show that it all depends on the quality of the water and the impurities that are added to it. The cause may be an old clogged pipe. Rust and other elements can get into the water by accident, but they will do a lot of troubles. Often the cause of the breakdown is determined by the faster movement of the device. The arrow starts to rotate much faster. You can compare these readings with a cold water meter, however, if this problem occurs in one pipe, there is no guarantee that the other pipe will be cleaner.
In order for the counter to last longer, it is enough to install a special filter on the pipe, which will block the access of large particles and fragments. From time to time the filters will have to be changed and the elements cleaned.
Deep filters allow you to place a small flask with a mesh inside the pipe. It consists of a special element made of stainless steel. Two nozzles fit this flask.
The cleaning process is quite simple. To do this, we need to do the following:
- Relieve pressure in the cleaning system.
- Using a special ring spanner we unscrew the hexagonal fasteners.
- After opening the filter, the mesh is carefully removed.
- The item is cleaned under water or manually.
- All components are dried and put in place in the reverse order.
In addition to filters with a sieve, there are filters with a special box - a cartridge. It contains various cleaning materials, such as coal and other impurities.
Cartridges do not need to be cleaned: they are disposable and can be simply thrown out after replacing them. The new element is replaced with the old one - and the device is ready for operation again.
Problem number 4: pressure change in pressure
Hot water meter does not spin: what to do? Quite a lot can depend on the pressure of the water in the pipes. It would seem that the device is designed to measure water, but no, and in this area it is not so simple. Any device has its own wear. The diameter of the pipes and the pressure created in them can destroy a completely new device. So, the arrow begins to gain speed and due to the dynamics, excess water is wound, for which you have to pay. The displacement may not be that big, but it's still your money.
It is also possible that a reverse situation occurs when there is almost no pressure in the pipes. Analyze the condition of the pipes and measure the pressure. Use available containers or simply estimate how much water you are using approximately.
Problem number 5: damage or breakdown of the meter itself
Often users of counters notice this problem: the head is turned on, but the arrow does not move. At another moment, it jerks or stops moving altogether. Reasons and solutions:
- Perhaps the device was originally defective or received some damage.
- During installation, it accidentally fell or knocked during transportation.
- If the device itself can be repaired, you should study the problem itself.
- If replacement of parts is not possible, it is better to buy a new counter.
Hot water meter does not spin: what to do? In any situation, if you notice this problem, do not try to fix it yourself. Call a specialist to inspect and repair the instrument.
Problem number 6: manual intervention in the operation of the device. What to do?
Does the hot water meter not work? First aid by the owner can only do harm. We remind you that it is strictly forbidden to open the counter yourself. For this you can get a fine. Many residents go to tricks, take off the device, twist the arrows to rewind the "excess", but do not think that it is possible to break the device and pay even more in the end.
There are a lot of ways to cheat. Devices purge, put magnets, ribbons, poke with needles to fix the arrow, and much more. Here, as they say, anyone has enough imagination. Such folk methods are a dime a dozen.
Problem number 7: very hot water. What to do?
The hot water meter stopped spinning? The cause of the breakdown of the device can also be covered in very hot water. Even the SVG is designed for a specific temperature of use. High temperature conditions knock down the readings and cause the device to lie or stop its work at all. The standard for tolerated temperatures for SVG is a 90 degree barrier.
If the water temperature is within the normal range, however, the specialist recorded a breakdown precisely for this reason, and the device is under warranty, then the consumer can easily use the repair at the expense of the manufacturer.
Do not neglect this problem, as ignoring the damage can result in a serious fine.
What should be done when a meter break is detected?
Hot water meter does not spin: what to do? First of all, if you notice a problem with the testimony, consult a specialist. Do not be silent, as the containment of information can be used against you and hang in the end a lot of debt.
A good proof of your reliability and a sign that you left a request to consider the health of your meter can be photographed readings with a clearly visible date. So:
- Contact the management company.
- Set a time so that the employee of the management company arrives to fix the breakdown.
- After checking, the employee decides what to do with the device.
Conclusion
So, take care of the device, do not hit, do not place or drop anything on it. Do not neglect the scheduled check (every 3-5 years). Do not be silent when a breakage is detected. Contact only specialists and record all their actions.
